SnowPlows Plus Inc.

Wireless remote control systems for gas salt sander spreaders. Controls, engine on, off, start, speed and conveyor / spinner on off. No mounting of huge and expensive control in the cab or wires run through the cab. All solid state industrial controller. Compare this to the price of a replacement controller alone.   service@snowplowsplus.com

CLICK HERE FOR INSTALLATION MANUAL

• 2 BUTTON REMOTE KIT
• STANDARD ANTENNA (UP TO 100' CLEAR LINE SITE) 
• 2 MOMENTARY FUNCTIONS-NO LATCHING
• POWERS UP WITH 6, 12 OR 24 VOLT

• 2 BUTTON REMOTE
• STANDARD ANTENNA (UP TO 100' CLEAR LINE SITE)
• 1 DOUBLE PULL CIRCUIT (OPERATE A VALVE AND A MOTOR ON A MOMENTARY BUTTON.)
• OTHER BUTTON IS A SINGLE FUNCTION MOMENTARY, NO LATCHING CIRCUITS.
• POWERS UP WITH 6, 12 OR 24 VOLT

• 2 BUTTON CONTROLLER
• 1 BUTTON SINGLE FUNCTION LATCHING (PRESS THE BUTTON ONCE TO ACTIVATE PRESS AGAIN TO DEACTIVATE.
• SECOND BUTTON IS MOMENTARY SINGLE FUNCTION (HOLD THE BUTTON DOWN TO ACTIVATE, RELEASE TO DEACTIVATE)
• UP TO 500' CLEAR LINE SITE OPERATION.
• POWERS UP WITH 6, 12 OR 24 VOLT

This controller includes the valve shown. Button 1 is a latching on/off function to open and close the valve. Button 2 is a optional momentary function which you can use for any momentary function you may need. This button with our optional ground relay kit can be used as an engine shut off function.

Unit is designed for air compressor air on / off control or water on / off control

This controller priced WITHOUT THE VALVE. Button 1 is a latching on/off function to open and close the valve. Button 2 is a optional momentary function which you can use for any momentary function you may need. This button with our optional ground relay kit can be used as an engine shut off function.

Unit is designed for air compressor air on / off control or water on / off control. For water control applications a simple sprinkler valve can be used.

• 4 BUTTON REMOTE
• 1 LATCHING CIRCUIT THAT UNLATCHES BY PRESSING ANY OF THE 3 OTHER BUTTONS.
• 3 DOUBLE PULL MOMENTARY FUNCTIONS (THE 3 BUTTONS WILL MOMENTARILY OPERATE A VALVE AND A MOTOR.  HOLD THE BUTTOM DOWN TO ACTIVATE, RELEASE TO DEACTIVATE)
• 4-BUTTON FUNCTION WIRELESS REMOTE CONTROL KIT.
• OPERATES AT DISTANCES UP TO 100' CLEAR LINE SITE
• HUNDREDS OF 12 VOLT DC APPLICATIONS
• COMES WITH 4 BUTTON KEYCHAIN REMOTE, RECEIVER WITH LEADS, AND WIRING DIAGRAM.
• ALL SOLID STATE CONSTRUCTION FOR INDUSTRIAL USE.
• POWERS UP WITH 6VDC-24VDC.

4 BUTTON REMOTE ALL FUNCTIONS MOMENTARY WITH EXTENDED RANGE ANTENNA (not shown) UP TO 500'

POWERS UP WITH 6, 12 OR 24 VOLT

RF600DC VARIABLE SPEED MOTOR CONTROLLER

  The RF-600DC Wireless DC Motor Controller provides RPM control for a single, 2 pole DC motor that can output 180 amps for up to 5 seconds and a continuous amperage of up to 80 amps. The speed or RPM control is done by providing the user 5 outputs, approximately 1/5 of the maximum motor RPM. The RF-600DC also incorporates a full RPM feature the runs the motor full speed for 6 seconds and then automatically shuts off and an E-Stop.

To protect the motor and electronics, the RF-600DC has built-in safety circuits. These include:·        Automatic shut down if motor is locked up. How this is done is if the receiver senses a current draw of more than 180 amps for more than 10mS the unit will shut down from 1 to 30 seconds.·        Automatic shut off if the current draw does not drop below 80 amps after 5 seconds. Once again, the receiver will shut down for 1 to 30 seconds. 

• 8 BUTTON REMOTE
• EXTENDED RANGE ANTENNA (up to 500' clear line site)
• ALL BUTTONS SINGLE MOMENTARY FUNCTIONS (HOLD THE BUTTON DOWN TO ACTIVATE RELEASE TO DEACTIVATE.)
• Operates at distances up to 500'
• POWERS UP WITH 6, 12 OR 24 VOLTComes with 8 button keychain remote, receiver with leads and wiring diagram

• 8 BUTTON CONTROL UNIT
•  EXTENDED RANGE ANTENNA (UP TO 500')
•  BUTTONS 1 AND 2 ARE ON OFF LATCHING (PRESS BUTTON ONCE TO TURN A FUNCTION ON, PRESS SAME BUTTON AGAIN TO TURN OFF)
• BUTTONS 3-8 ARE SINGLE MOMENTARY FUNCTIONS (HOLD THE BUTTON DOWN TO ACTIVATE A FUNCTION & RELEASE THE BUTTON TO DEACTIVATE) 
•  UP TO 500' RANGE CLEAR LINE SITE OPERATION
• POWERS UP WITH 6, 12 OR 24 VOLT

• This kit allows you to change one of the positive outputs of the remote to a ground output. Example - Engine kill switch.
•  This will work with all of our controllers on any momentary function available.
• Comes with complete instructions.

Use this reverse polarity contactor with one of our wireless systems to run motors forward and reverse. (Motor must be designed to handle this) Most winch motors, ATV Winch,gear motors etc... are designed this way.

Bosch 12 volt throttle actuator and for many other uses.

Link to specifications sheet

• THE NEW LT9 FCC APPROVED INDUSTRIAL TRANSMITTER
• 9 BUTTONS ON A LARGE PLATFORM
• MEASURES 5-1/2" TALL x 3-1/3 WIDE.
• CAN BE USED WITH ALL CAW's RECEIVER UNITS.
• SHIPPING OF $7.50 ON THIS ITEM WILL BE ADDED TO ORDER

• CAN BE USED AS A REPLACMENT OR SPARE TRANSMITTER.
• WILL NOT INTERFERE WITH YOUR ORIGINAL TRANSMITTER.
• EASILY PROGRAMMED.
• 1 IN 16 MILLION ADDRESS COMBINATIONS.
• UP TO 20 TRANSMITTERS CAN BE MATCHED TO 1 RECEIVER.
• SHIPPING OF $6.50 ON THIS ITEM WILL BE ADDED TO ORDER.

• CAN BE USED AS A REPLACMENT OR SPARE TRANSMITTER.
• WILL NOT INTERFERE WITH YOUR ORIGINAL TRANSMITTER.
• EASILY PROGRAMMED.
• 1 IN 16 MILLION ADDRESS COMBINATIONS.
• UP TO 20 TRANSMITTERS CAN BE MATCHED TO 1 RECEIVER.
• SHIPPING OF $6.50 ON THIS ITEM WILL BE ADDED TO ORDER.

• CAN BE USED AS A REPLACMENT OR SPARE TRANSMITTER.
• WILL NOT INTERFERE WITH YOUR ORIGINAL TRANSMITTER.
• EASILY PROGRAMMED.
• 1 IN 16 MILLION ADDRESS COMBINATIONS.
• UP TO 20 TRANSMITTERS CAN BE MATCHED TO 1 RECEIVER.
• SHIPPING OF $6.50 ON THIS ITEM WILL BE ADDED TO ORDER.